HPE Juniper Networking JN0-364 Certification Exam Sample Questions and Answers

JNCIS Service Provider Dumps, JN0-364 Dumps, HPE Juniper Networking JNCIS-SP PDF, JN0-364 PDF, JNCIS Service Provider VCE, HPE Juniper Networking JNCIS Service Provider Questions PDF, HPE Juniper Networking Exam VCE, HPE Juniper Networking JN0-364 VCE, JNCIS Service Provider Cheat SheetBefore you write the HPE Juniper Networking JNCIS Service Provider (JN0-364) certification exam, you may have certain doubts in your mind regarding the pattern of the test, the types of questions asked in it, the difficulty level of the questions and time required to complete the questions. These HPE Juniper Networks Certified Specialist - Service Provider Routing and Switching (JNCIS-SP) sample questions and demo exam help you in removing these doubts and prepare you to take the test.

The best approach to pass your HPE Juniper Networking JN0-364 exam is to challenge and improve your knowledge. To test your learning and identify improvement areas with actual exam format, we suggest you practice with Premium HPE Juniper Networking JN0-364 Certification Practice Exam. The practice test is one of the most important elements of your HPE Juniper Networking Service Provider Routing and Switching Specialist (JNCIS-SP) exam study strategy to discover your strengths and weaknesses, to improve your time management skills and to get an idea of the score you can expect.

HPE Juniper Networking JN0-364 (JNCIS-SP) Sample Questions:

01. Two PE routers run an IBGP session between their loopback addresses across several P routers. You want the IBGP session itself to be declared down in well under a second when the two PEs lose reachability to each other.
Which approach meets this requirement?
a) Run single-hop BFD on the core interfaces of every P router.
b) Enable BFD for the IBGP neighbors, which runs as multihop BFD.
c) Enable nonstop active routing on both PE routers.
d) Lower the BGP hold time on both PE routers to its minimum value.
 
02. A service provider has configured GRES and graceful restart, but not NSR, on its dual-RE MX Series routers. During a Routing Engine switchover test, the OSPF adjacencies with the neighboring routers reset.
What is the most likely reason?
a) OSPF graceful restart works only on point-to-point interfaces, so broadcast adjacencies reset.
b) GRES discards kernel state during the switchover, so the new primary RE must relearn every OSPF route.
c) The neighboring routers are not acting as graceful restart helpers.
d) BFD is not configured, so OSPF cannot signal the restart to its neighbors.
 
03. You authenticate OSPFv2 with MD5 on the IPv4 link between R1 and R2, and you must now authenticate the OSPFv3 packets they exchange on ge-0/0/1.0.
Which two statements about this task are correct?
(Choose two.)
a) Both interfaces need global addresses from one shared /64 before authentication can work
b) The OSPFv3 packet header has no authentication field, unlike the OSPFv2 header
c) An IPsec security association applied with ipsec-sa on the OSPFv3 interface authenticates the packets
d) Listing ge-0/0/1.0 under protocols ospf with MD5 also authenticates its OSPFv3 packets
 
04. Which three statements are true about RSVP LSPs configured with the fast-reroute statement on Junos devices?
(Choose three.)
a) Fast reroute can detour around node or link failures.
b) Fast reroute is configured on every transit router along the LSP.
c) The ingress router does not signal a new path for the LSP after traffic moves onto a fast reroute detour.
d) Fast reroute uses the traffic engineering database to calculate the detours.
e) Detour paths are immediately available.
 
05. By default, which router pops the label from a packet on a single-label LSP in a Junos MPLS network?
a) the egress router
b) the penultimate-hop router
c) the ingress router
d) the first transit router after the ingress
 
06. The egress router of an IPv4 RSVP-signaled LSP is configured with explicit-null. Which label value does it advertise to the penultimate router?
a) 0
b) 2
c) 3
d) 1
 
07. An established RSVP-signaled LSP suffers a link failure. The router immediately upstream of the failed link (on the ingress side) detects the failure.
Which statement describes one of the messages this router sends?
a) It sends a ResvTear message downstream toward the egress.
b) It sends a ResvErr message upstream toward the ingress.
c) It sends a PathTear message upstream toward the ingress.
d) It sends a ResvTear message upstream toward the ingress.
 
08. Root protection is configured on an MX Series interface that connects to an access switch. The access switch begins sending superior BPDUs on that link.
What happens to the interface?
a) It blocks in a loop-inconsistent state until it receives BPDUs again
b) It becomes the root port, and the access switch becomes the new root bridge
c) It blocks in a root-prevented state until the superior BPDUs stop
d) It is disabled in an error state until an operator clears the error
 
09. You configure set protocols isis reference-bandwidth 40g on a router and set no metric on any IS-IS interface. Which metrics do its 10GbE and 1GbE interfaces receive?
a) 10GbE: 40, 1GbE: 4
b) 10GbE: 4, 1GbE: 40
c) 10GbE: 1, 1GbE: 10
d) 10GbE: 10, 1GbE: 10
 
10. Interface ge-0/0/0.0 connects your network to your ISP. You want OSPF to advertise this interface's subnet as an internal route without forming an OSPF neighbor relationship with the ISP.
How should you accomplish this task?
a) Add ge-0/0/0.0 to OSPF with interface-type p2p.
b) Set the OSPF priority of ge-0/0/0.0 to 0.
c) Export the ge-0/0/0.0 direct route into OSPF.
d) Add ge-0/0/0.0 to the OSPF area as a passive interface.

Solutions:

Question: 01

Answer: b

Question: 02

Answer: c

Question: 03

Answer: b, c

Question: 04

Answer: a, d, e

Question: 05

Answer: b

Question: 06

Answer: a

Question: 07

Answer: d

Question: 08

Answer: c

Question: 09

Answer: b

Question: 10

Answer: d

Note: If you find any error in these HPE Juniper Networking HPE Juniper Networking Service Provider Routing and Switching Specialist (JNCIS-SP) sample questions, you can update us by write an email on feedback@nwexam.com.

Rating: 4.8 / 5 (279 votes)